泰安附近想过夜电话联系

Zhongwei water tank customized Wuzhong water tank wholesale regular stainless steel water tank

07-13 one thousand and forty-eight

Zhongwei water tank Customized Wuzhong water tank Wholesale regular stainless steel water tank

Features of Zhongwei water tank stainless steel domestic water tank

1. Stainless steel water tank is generally made of SUS304 stainless steel plate, with stable physical and chemical properties, no pollution to water quality, and clean and sanitary water quality.

2. Stainless steel water tank stamping molding, high strength, light weight, neat appearance, elegant appearance.

3. The surface of the water tank is generally bright and clean.

4. Due to the dense oxide layer on the surface, it has excellent corrosion resistance and good sealing performance.

5. High impact resistance and strong seismic performance. According to the different ways of use, it can be divided into two modes: all-weather water supply is mainly used in hotels, hotels, hospitals and other places, and regular water supply is mainly used in schools, factories and other places. The installation method of timing water supply is relatively simple. As long as two circulating pipes are installed on the water tank and the main engine for circulating heating, and then the hot water is used up in a certain period of time, and then the cold water is added again to reheat it. This installation method is very energy-saving. There are a lot of installation methods for all-weather water supply, such as direct heating type, circulating type, large and small water tank mode and so on. Direct heating means that the hot water heated by the main engine can be used directly, and the outlet temperature can reach 45-55 ℃. This principle is to control the amount of make-up water through a throttling device. The water flow can not fill the whole heat exchanger. Therefore, when making a direct heating host, it is necessary to consider that the diameter of the heat exchanger cannot be too large, and the most reasonable pipe diameter and water discharge mode should be selected after repeated debugging.

Specification of square stainless steel domestic water tank for Wuzhong water tank

Cleaning of square stainless steel domestic water tank

1. Close the inlet valve and open the drain outlet valve to drain the water in the water tank;

2. Access to water tank through ladder;

3. Clean the periphery and bottom of water tank with clean mop or cloth. If the scale is serious at the bottom, it can be scrubbed with soft towel and detergent;

4. Open the water inlet valve and flush the wall and bottom of the barrel with proper amount of clean water, so that the dirt can be discharged from the drain outlet. If necessary, it can be repeated several times until it is satisfactory;

5. Close the drain valve, open the water inlet valve, and fill the water tank with water again.

Installation and commissioning of square stainless steel domestic water tank in Wuzhong water tank

1. The water tank is full of water and there is no leakage in 24 hours;

2. Whether there is water leakage at the pipe joints, valves and relevant accessories;

3. Observe whether the water supply system operates normally;

4. Check whether the water disinfection system works normally. The most common water tank is round. Now many water tanks are square. What is it? This is of course related to the characteristics and differences of the two tanks. Those who have studied physics know that this should be common sense. Stainless steel water tower is used for water storage. The pressure at the bottom is higher, so the higher the tonnage of the tank, the higher the pressure in the same installation area. The larger the stainless steel wall thickness of the water tank is. With the increase of the tonnage of stainless steel circular water tank, the greater the water pressure at the bottom, the cylindrical water tank can roll on the lower box, through rolling to improve the strength and ensure the service life and performance. However, when the tonnage of the water tank is too large, this method does not meet the synthetic benefit to a certain extent, and the performance and service life are not up to the standard. This is a stainless steel square tank. The thickness of stainless steel circular water tank is generally 0.5mm, the thickness is 0.5-2.5t, 0.6mm, 3.4-5.0t, and the thickness is 0.7-1.0mm, 5.0 or greater.

Wuzhong stainless steel water tank Cleaning and maintenance of Zhongwei water tank
1. Close the inlet valve and open the drain outlet valve to drain the water in the water tank;
2. Enter the water tank through the ladder;
3. Clean the periphery and bottom of water tank with clean mop or cloth. If the scale is serious at the bottom, it can be scrubbed with soft towel and detergent;
4. Open the water inlet valve and flush the wall and bottom of the barrel with proper amount of clean water, so that the dirt can be discharged from the drain outlet. If necessary, it can be repeated several times until it is satisfactory;
5. Close the drain valve, open the water inlet valve, and fill the water tank with water again.
Wuzhong water tank specifications Zhongwei water tank specifications can be formulated according to the specifications required by customers; Ningxia Jiquan water supply equipment Co., Ltd. welcome to discuss 180-95174046; we will serve you wholeheartedly!